Roper Dryer Parts

Dryer drum drive belt. The belt is flat, 92-1/4 inches long, 1/4 inch wide and has 4 ribs and 3 grooves. It replaces many other belts, including some with 5 ribs and 4 grooves. If the drum does not turn, but you can hear the motor running then there is a good chance the belt has broken.

OEM Part - Manufacturer #341241

Consider replacing the idler assembly while you have the dryer apart.

Dryer gas burner valve solenoid set. If the dryer does not heat or heats intermittently the coils could be defective. To test, watch the burner and if the igniter glows for a while and then shuts off without the gas igniting, it usually means one of these coils is bad.

OEM Part - Manufacturer #279834

Dryer heating element. If your dryer does not heat first check for a blown thermal fuse on the blower housing before replacing the heating element. In most cases the heating element will have a break in the element if defective.

OEM Part - Manufacturer #279838

The heating element and many other parts can be tested using a volt/ohm meter which is a handy item to have in any do it yourselfers tool box.

Dryer heating element thermal cut-off (thermal fuse) 309 degrees and high limit thermostat 250 degrees, with wiring kit. If the dryer does not heat the thermal cut off may have blown and a new high limit thermostat is needed.

OEM Part - Manufacturer #279816

Dryer door switch assembly. If the dryer does not start then the door switch could be defective. This switch also replaces the two wire switch.

OEM Part - Manufacturer #WP3406107

Dryer tri-ring retainer for drum support rollers.

OEM Part - Manufacturer #WPW10512946

Dryer cycling thermostat with internal bias heater, L155-25. If the dryer won't heat, it is unlikely that this thermostat is causing the issue, as the thermal fuse or thermal cut-out normally fail first.

OEM Part - Manufacturer #WP3387134

Dryer igniter kit. This igniter will replace both round and flat style igniters. The kit includes the bracket, wire nuts and mounting screw. Be aware the igniter is very fragile and should be handled carefully.

OEM Part - Manufacturer #279311

Consider replacing the gas valve coils while you have the dryer apart.

Rear drum support roller kit. This kit contains two drum support rollers. If the drum rollers are worn out, the dryer may not turn properly or may be excessively noisy. Be aware that the drum bearings are self-lubricating; it is not necessary to lubricate them yourself.

OEM Part - Manufacturer #349241T

The drum rollers and drum roller axles often wear out at the same time. If the drum roller axles are worn out, replace them along with the drum rollers.

Dryer door catch kit. This kit includes three different door catches; you will need to select the door catch that fits your model.

OEM Part - Manufacturer #279570

Dryer high-limit thermostat, L250-80, with terminal extension arm. This thermostat should be closed for continuity at room temperature and opens at around 250 degrees Fahrenheit. If the dryer won't heat, the high-limit thermostat might be defective.

OEM Part - Manufacturer #WP3977767

The part may look different than the original but the part will still install and work the same.

Dryer belt tension idler pulley assembly.

OEM Part - Manufacturer #WP691366

Consider replacing the Drive Belt while you have the dryer apart.

Dryer lint screen assembly. Proper air flow is critical to dryer operation so the filter should be cleaned before every load.

OEM Part - Manufacturer #WPW10717210

Heating element thermal cut-off (thermal fuse) 360 degrees and high-limit thermostat 250 degrees. The thermal fuse is a safety device designed to protect the dryer from overheating. A multimeter can be used to test the fuse. Always check the dryer venting when replacing a blown thermal fuse.

OEM Part - Manufacturer #279769

The fuse can be tested using a multimeter meter

Dryer heating element assembly, 240 volts. If the dryer does not heat check for a blown themal fuse or thermal cut out. Heating elements will often have a break in the coil element if defective.

OEM Part - Manufacturer #WP4391960

If the terminal that connects to the element was damaged a new terminal can be spliced into the exsisting wiring harness.

Dryer L.P conversion kit Natural gas to LP (liquid propane). This kit includes the orifice, leak limiter, and instruction sheet.

OEM Part - Manufacturer #W10606694A

Repair kit for Whirlpool, Kenmore, Roper dryer; rollers, belt and idler pulley, for 29" wide Dryers built 1965 and later. This dryer maintenance kit contains all of the parts that are commonly defective when the dryer is noisy.
-Call with model# to verify if kit is compatible with your dryer.

OEM Part - Manufacturer #4392065

Screw

OEM Part - Manufacturer #WP308685

Gas dryer sensor for igniter and flame. The sensor is located across from the gas igniter at the dryer’s burner assembly. This flame sensor should be closed for continuity at room temperature. Check for continuity with a multi-meter before replacing.

OEM Part - Manufacturer #WP338906

Lint Filter with Cover

OEM Part - Manufacturer #W10828351

If the lint filter cover is damaged or cracked, it should be replaced.

Light bulb, 10 watt.

OEM Part - Manufacturer #WP22002263

Dryer LP (liquid propane) conversion kit. From Natural gas to LP.

OEM Part - Manufacturer #49572A

Lint filter with handle, measures 20 3/4" x 7 1/2". This filter should be cleaned before every load to ensure proper airflow for dryer operation. If the lint filter is ripped or torn, replace it.

OEM Part - Manufacturer #WP349639

Use this brush to clean the dryers venting.

Cleaning brush for refrigerators, freezers, dryers and more. This brush is perfect for cleaning condenser coils on refrigeration systems. It is important to regularly clean the condenser coil to ensure the refrigerator is running efficiently.

OEM Part - Manufacturer #4210463RW

Pair this tool with this vacuum extension tube and easily clean under appliances without having to move them.

Dryer lint screen assembly with handle

OEM Part - Manufacturer #339392V

Dryer push to start switch. If the dryer doesn't start then the start switch may be defective. The switch can be tested to determine it is bad using a multi-meter.

OEM Part - Manufacturer #WP3977456

White touch-up paint

OEM Part - Manufacturer #72017

Dryer drum drive motor. Includes pulley for dryer drum drive belt. Other shaft has reverse threads for blower wheel. Common symptoms of a bad drive motor are:
-Dryer stops turning during cycle
-Dryer won't start
-Dryer won't turn at all
-Dryer drive motor is loud

OEM Part - Manufacturer #279827

Dryer blower wheel. Used on 29 inch Whirlpool built models with lint filter on top. To remove the blower wheel, unscrew the blower wheel clockwise off the motor shaft.

OEM Part - Manufacturer #WP694089

Dryer drum felt seal kit with adhesive and instructions.

OEM Part - Manufacturer #W10612022

Dryer gas burner high limit thermostat and thermal fuse kit. If the dryer does not heat the most common cause is a blown thermal fuse. Both the thermostat and fuse can be tested to determine if either is defective.

OEM Part - Manufacturer #W10480709

Dryer door/washer lid switch kit

OEM Part - Manufacturer #W10820036

Dryer door switch assembly. If your door switch is defective, the dryer will not start.

OEM Part - Manufacturer #WP3406105

Use a multimeter to test your door switch for continuity.

Dryer vent cleaning brush. This brush is designed for cleaning 4-inch diameter ducts. At 20 feet in length, it provides substantial reach.

OEM Part - Manufacturer #18001034

High-limit thermostat. If the dryer overheats, the high-limit thermostat cuts off power to the dryer. If the dryer won't heat, the high-limit thermostat may have blown. This part has been updated by the manufacturer. The new thermostat may differ in appearance, but will have the same function.

OEM Part - Manufacturer #WPW10423382

Dryer timer. The timer controls the dryer operations. Be aware that the dryer must heat properly for the timer to advance in an automatically timed cycle.

OEM Part - Manufacturer #WPW10185972

Ring bearing kit, front of dryer drum

OEM Part - Manufacturer #279441

Dryer push-to-start switch. If this switch is defective, the dryer will not start.

OEM Part - Manufacturer #WP3398095

Heating element wire connector kit for electric dryers. If the wire & connector at the dryer heating element is bad this wire connector kit can be used to repair it.

OEM Part - Manufacturer #279457

Lint Screen

OEM Part - Manufacturer #W10874409

Dryer foam seal with adhesive backing. This seals goes between the lint chute and the bulkhead.

OEM Part - Manufacturer #WP339956

Motor pulley, 60 hertz

OEM Part - Manufacturer #WP8066184

Shaft for drum support roller, left side

OEM Part - Manufacturer #WPW10359270

Dryer blower housing foam seal with adhesive backing.

OEM Part - Manufacturer #WP347139

Spray paint, white, 12 ounces

OEM Part - Manufacturer #350930

Shaft for drum support roller, right side

OEM Part - Manufacturer #WPW10359269

High-limit thermostat, 2 wire, 250 degree limit, 60 degree cool down before reset. The high-limit thermostat cuts off power to the dryer if it overheats. If the thermostat has tripped, the dryer will not heat. To determine if the thermostat is defective, use a multimeter to test it for continuity.

OEM Part - Manufacturer #WP3390291

Touch-up paint, biscuit, .6 Fl. Oz.

OEM Part - Manufacturer #4392899